SPECIFICATION
CONSTRUCTION
RCD Status:
• CE Certification Directive 94/25/CE (Category "A" Ocean)
Hull Construction:
• The hull is hand laid up using three layers of TWARON; a carbon aramid (Kevlar) fibre with alternating FRP (fibre reinforced plastic) glass lay up.
• A solid laminate (ie. no core) is used for maximum strength and longevity.
• Modern vinylester resins and isophthalic gelcoats are used for increased resistance to the effects of osmosis.
• The gelcoat finish is white with blue style lines.
• Original Coppercoat removed, hull sanded back and 4x new epoxy coatings applied – 2020
• International Micron 350 antifoul – Spring 2023
• The hull sides feature a teak rubbing strake with stainless steel capping. This rubbing strake runs the length of the hull sides.
• The bow area is further protected by a stainless-steel strike plate in the general anchor area. A protective stainless-steel plate can also be found at the transom.
• Internally, a watertight collision bulkhead is found ahead of the forward cabin with independent overboard drainage.
• Aft are watertight stern sections protecting the owner’s cabin from water ingress to the aft lazarettes and stern lockers.
Deck & Superstructure Construction:
• Balsa-cored GRP deck & with solid GRP laminate used beneath deck fittings and in high-stress areas.
• Additional layer of TWARON built into coachroof
• The deck and forward coachroof are overlaid with hand-picked teak planking. The decks were fully renovated including full recaulking - 2021
• Areas not covered in teak are finished in a high quality grey non-slip GRP finish.
• The cockpit seating and bathing platform are also teak laid with teak grating above the cockpit sole
• Raised solid teak bulwark is fitted along the lengths of the deck with stainless steel fairleads in way of mooring cleats.
• The superstructure and forward coachroof also feature stainless steel or teak grab rails
• Ventilation to below decks is via a number of opening alloy deckhead hatches, stainless steel cowl vents and stainless steel opening side ports.
Keel & Rudder:
• The keel is a fin section with a slight bulb to the base.
• The keel material is solid lead, attached to the GRP bilge with 8x 35mm acid resistant stainless-steel bolt with transverse mounted 8mm backing plates.
• The rudder is a semi-skegged GRP blade for optimal performance, strength and protection.
• Replacement of rudder packing - 2022
• The draft of the rudder is less than the keel, to ensure full protection in case of accidental grounding.
MACHINERY
Engine & gearbox:
• Yanmar 4JH-series 125hp 4 cylinder turbocharged diesel engine with cockpit controls and alarm system
• Approximately 1,650 hrs run as of Spring 2024
• Engine service – Spring 2024
• Freshwater cooling system via raw water intake and heat exchanger
• Yanmar reduction gearbox
• Morse single lever control system to protect against high RPM gear shifting
• Dual Racal fuel filtration system allowing independent filter and bypass system
• Walborough in-line fuel system allowing engine bypass for filtration and eliminating the need for future engine bleeding in the case of a dry fuel tank
• Oil change pump built in as standard
• Engine room sound insulation, fire retardant
• Fuel cleaning and polishing system - 2021
Propulsion & Steering:
• Brunton Varifold 4-bladed folding propeller
• Propspeed prop treatment - 2020
• 1 ½” stainless steel propeller shaft
• Flexible shaft coupling
• Shaft brake
• Non-drip shaft seal
• Whitlock Lewmar pedestal with offset pedestal for instrument mounting and binnacle compass
• Whitlock large diameter hide-covered stainless steel helm wheel with cable linkage to quadrant
• 24v Sleipner Sidepower bowthruster with control at helm pedestal
• Emergency steering gear
ELECTRICAL SYSTEMS
Voltage systems:
• 12 & 24vDC domestic systems with 220vAC via shorepower or inverters
Battery Banks:
• 1x 12vDC 125Ah AGM engine start battery
• 12vDC Victron AGM service batteries joined in parallel and series to supply 660Ah @ 24vDC - 2023
• 2x 12vDC 200Ah AGM batteries for bowthruster, genoa furling and anchor windlass
• Victron BMV-501 battery monitoring system
• All batteries are isolated with a built-in reverse isolation switch
• All batteries self-contained and strapped in place
Charging:
• 3x Victron Multi Pheonix 24vDC chargers with 3kw inverters linked in parallel
• 1x Protech 12vDC 50Amp automatic battery charger for engine/generator start
• Victron Pheonix Multi-Control for primary battery charger/inverters - 2020
Alternators:
• Yanmar engine-mounted alternator (12v)
• Balmar high output 24vDC alternator
• Balmar MaxCharge voltage regulator for high output alternator
Generator:
• Fischer Panda DC variable speed 8kva generator
• Generator removed and overhauled by Fischer Panda – Winter 2018/19
• Approx 1,240 hrs run as of Spring 2024
• Date of last generator service – Spring 2024
Solar:
• 740 W Victron Solar Power panel array mounted to custom fabricated stainless steel frame over cockpit with Victron Monitoring Display – 2021/23
Other Electrical:
• Marinco 32Amp 50Hz 230vAC shore power system with ring-main and 220vAC sockets throughout yacht.
• 220vAC ring main with sockets throughout
• Main AC/DC control panel with V, A & Hz meters
• Wiring "tinned" to reduce corrosion
• Two 3" copper strips running bow to stern both port and starboard for grounding
• Galvanic isolator with status monitor
PLUMBING & GAS SYSTEMS
Fresh Water:
• Two independent DC freshwater pump systems with visual indication lights at AC/DC panel
• Manual freshwater pump, foot activated for freshwater accessed in the galley
• Hot water supply via engine calorifier and 220vAC 1,500w immersion heater element in 10 US gallon hot water tank powered by shorepower
• Calorifier tank replaced Spring 2019
Watermaker:
• Seafari Mini 350 modular watermaker – 220vAC
• Supplied and fitted by Fischer Panda – Spring 2019
Bilge Pumps:
• Two independent DC bilge pump systems
• Total of 2000 gallons/hour with Bilge Bug conductive switches
• Third DC bilge pump system for lazarette
• Manual bilge pump in cockpit
Other Plumbing:
• All through hull fittings are solid bronze and all are bonded
• Saltwater deck wash
• Pressurised cockpit shower
TANKAGE
Fuel:
• 1,246 litres of total fuel tankage in four independent stainless-steel tanks
• All tanks have easy access for inspection with dipstick, threaded inspection cap and larger inspection port
• Tank Tender system for monitoring tank levels
• Fuel manifold system with electric fuel transfer pump
Fresh Water:
• 895 litres of total water tankage four independent stainless steel tanks
• All tanks have easy access for inspection with dipstick, threaded inspection cap and larger inspection port
• Tank Tender system for monitoring tank levels
Holding Tanks:
• 140 litres independent holding tank for forward heads
• 102 litres independent holding tank for aft heads
• Dual Y valve system for deck pump out, and direct pump out overboard with independent hand pump
• Tankwatch 4 level monitoring systems at both heads
NAVIGATION & COMMUNICATION EQUIPMENT
At Helm:
• 2x B&G Triton multi-displays – 2014
• B&G Zeus3 in aft cabin with separate battery and switch for lightning - 2020
• B&G Triton autopilot control (2021) attached to B&G NAC-3 autopilot computer (2024)
• Ritchie Powerdamp binnacle compass
• Scanstrut pod mounting system
At Companionway:
• B&G Z12 12” colour radar/chart plotter display with Scanstrut pod – 2014
• Simrad Navico NAIS-300 Class B AIS transceiver connected to plotter displays – 2014
• Simrad closed-array 4G radar scanner on mast (2019)
• 3x B&G Triton multi-displays -2014
At Chart Table:
• B&G Z12 12” colour radar/chart plotter display – 2014
• 2x B&G Triton multi-displays – 2014
• B&G Triton autopilot control – 2021
• Furuno NX300 navtex display
• Extensive selection of Charts UK to Med, Caribbean and Atlantic
• Cruising Guides
Communications Equipment:
• B&G VHF H90 - 2020
• Simrad VHF speaker with secondary speaker at companionway
• Icom IC-M802 SSB with external speaker
• Pactor modem for SSB
• Simrad Nera 33 Inmarsat Fleet satellite phone with MS33 Satcom control system
• Iridium GO! system with antenna kit - 2019
DOMESTIC EQUIPMENT
Galley:
• Force 10 three burner stove with oven and grill
• Sharp 800w Dual-Grill microwave
• Large twin FrigoBoat DC Freezer/Refrigeration system with keel coolers, thermostatic controls and temperature gauges
Heads:
• 2x Vacuflush DC electric freshwater heads
• Zanussi FC1200w washing machine in locker outboard of aft shower cubicle
• Hot & cold pressurised water supplies with dedicated shower cubicles
Air Conditioning & Ventilation:
• Cruisair 220vAC reverse-cycle air-conditioning system with 16,000BTU unit in saloon, 11,000BTU in aft cabin and 11,000BTU in forward cabin (can run from DC generator via Victron inverters) – serviced 2020
• DC fans throughout interior
Lighting:
• Internal lighting: Halogen & LED DC
Entertainment:
• Phillips 24” LCD TV on motorised bracket in saloon
• Glomex amplified TV aerial
• Fusion Bluetooth radio/stereo system with Fusion waterproof cockpit speakers - 2020
ACCOMMODATION
Summary of Accommodation:
• Two double cabins with ensuite heads plus further converting double and sea-berths in saloon
Accommodation Finish:
• Customised teak interior
• Solid teak and holly soles laid on subflooring with epoxy urethane coating and seven layers of varnish
• Solid teak doors and trim
• Finely finished cabinetry with a choice of solid or louvered finish
• Solid teak handrails throughout the interior for easy movement offshore
• Abundant overhead hatches and ports for excellent ventilation
• Epoxy sealed endgrains and subflooring
• All cabin sole pieces are positive locking for offshore passage making
• All cabinets are finished throughout including complete interiors
• All overhead headliner are easily removed
• Santos (similar to Alcantara) upholstery throughout – pale green in saloon and blue in accommodation cabins
• Textured off-white headlinings
• Oceanair blinds throughout including deck saloon
• Split bunks in forward and aft cabins with lee cloths where necessary
Description of Accommodation from Forward:
Forward Cabin
• Full double berth 6′ 9" in length
• Three rows of two drawers underneath berth
• Cabinets above the berth for added storage
Forward Heads:
• Laminated counters with Moen faucet
• Heads with holding tank
• Dedicated shower cubicle
• Access from forward cabin or main corridor
Midships Cabin:
• Aft of the forward cabin to port.
• Upper and lower berth.
Main Saloon:
• Burr wood dinette.
• Full length starboard settee extends a further 9" for wide sea berth
• All tankage in main saloon is located below the sole allowing extensive storage under all seating areas and behind the dinette and settee
• Double walk through passageway offering optimal ventilation and movement throughout the interior
• Slide out seat with storage for added seating which slides in while underway
• Custom TV cabinet area
• Built in cocktail cabinet
• Maximum headroom just under 7′
Galley:
• Galley is over 7' in length to aft cabin offering total safety with roam to brace on either tack while offshore
• Ample cabinets, storage lockers and drawers including full length pantry for cutlery, cookware and food storage
• Slide out trash container with positive locking door
• Force 10 three burner stove with Xintex propane monitor and two sensors
• Large Frigo-0-Boat Freezer/Refrigeration system with thermostatic controls and temperature gauges
• Freezer/Refrigeration boxes have electric pumps for keeping drained, and are both top and front loading
• Counter top recesses over stove allowing for stainless steel backsplash and increased counter space when in place
• Manual foot pump for fresh water
• Wahlee stone counters
Navigation Station:
• Customised nav station with adjustable swivel chair
• Split instrument panel for instant access to wiring harness and connections
• Fast pin access to complete wiring harness and breakers
• All instruments and systems well labelled inside and out and traced numerically
Aft Cabin
• Queen size aft berth set on centreline with split mattress and accompanying starboard side settee
• Port and starboard side hanging lockers with optional removable shelves
• Full length deep hanging locker on centreline
• Portside vanity unit with fold up mirror and drawer with three separate cupboards
• Cupboards or drawers available under owner’s berth
Aft Head
• Laminated counters with Moen faucet
• Storage lockers in head
• Heads with holding tank
• Dedicated shower cubicle
• Large dedicated linen closet used for washer/dryer location
DECK EQUIPMENT
Rig:
• Selden white-painted aluminium mast keel-stepped mast
• Schaefer mast turning blocks
• Selden electric inmast furling system with buttons in cockpit
• White painted Selden boom
• White painted Selden rod vang with control line led aft to cockpit
• Triple in-line spreaders
• Discontinous stainless steel rigging with Sta-Lok rigging screws – Standing rigging replaced 2020
• Mast unstepped during winter 2023/23 and inspected.
• Running rigging replaced with cruising and racing Dyneema - 2021
• Forward and aft lowers for rig stability
• Insulated split backstay
• Lewmar adjustable mainsheet track
• Bamar MEJ 1-02 electric genoa furler
• Harken stand-up genoa sheet blocks
• Removable inner forestay for staysail
• Inner forestay deck and mast fittings for future fitment of staysail foil and furler
• Lewmar genoa tracks with cars for genoa and staysail
• Further jib tracks on coachroof
• White carbon fibre spinnaker pole – mast-mounted
• Removable stainless steel bowsprit for furling cruising chute
• Spinlock clutches
• Checkstays
• Gybe preventer
• Spinnaker halyard
• Staysail halyard
Winches:
• 2x Antal W66 2-speed electric self-tailing primary winches
• 2x Antal W52 2-speed manual self-tailing secondary winches
• 1x Antal W48 2-speed manual self-tailing outhaul and vang winch at companionway
• 1x Antal W48 2-speed electric self-tailing mainsheet winch aft of cockpit
• 2x Lewmar 54ST manual 2-speed self-tailing mast-mounted halyard winches
• All winches professionally serviced 2020
Sails:
• Jeckells Dacron inmast furling mainsail – 2018
• Furling Dacron genoa – 2008 (Serviced 2022)
• Hanked Dacron staysail – 2008
• Stormsail - 2020
• Channon Sails cruising chute with snuffer – 2006/7 (lightly used)
General:
• 32" high stanchions with double lifelines
• Side boarding ladder with port and starboard mounting brackets
• Manship 316 stainless overhead hatches and ports throughout
• Stainless steel handrails on foredeck coachroof and aft coachroof
• Stainless steel companionway handrails
• Solid teak cockpit table with teak drinks holder, varnished
• Solid stainless cowl vents : 4 in total – one pair forward, one pair aft
• Stainless protective stern plate
• Fresh water hot and cold shower on stern steps
• Fold-down stainless-steel stern ladder
• Removable chocks for tender (can be mounted on foredeck or across aft deck)
• Stainless steel antennae pole at transom with satellite phone and Navtex aerial
• Stainless steel pushpit cradle for liferaft
• Outboard bracket
Anchoring & Mooring:
• Solid stainless stem head fitting with split bow roller with stowage for two anchors
• Solid stainless steel striker plates for bow protection
• Maxwell Nilsson 3500 3.5kw windlass with chain feed stainless plate for chain protection plus bow controls and remote cockpit windlass control
• Maxwell Autoanchor 500C chain counter and cockpit windlass control
• 32kgs Delta anchor with 90mm of 3/8” galvanised chain
• Saltwater washdown at bow
• Two pairs of stainless steel bow cleats : one pair of 12" midship cleats and one pair of 12" stern cleats
• Fore and aft mooring lines
• Fenders
• Inflatable fenders - 2021
Dinghy & Outboard:
• Highfield inflatable dinghy – 2021
• Mercury 15hp 4-stroke outboard – 2022
• 8hp Yamaha outboard
Covers, Cushions & Canvas:
• CJ Marine canvas sprayhood with stainless steel grabrail
• CJ Marine canvas bimini
• CJ Marine canvas helm pedestal and wheel cover
• Blue vinyl cockpit cushions
Spares Inventory:
EN-DEILIG is offered for sale with an extensive spares inventory suited for offshore bluewater cruising, including:-
• Spare engine starter motor
• Spare alternator
• Spare fuel pump
• Spare bilge pump
• Filters, belts, impellers, servicing tools/ kit, oil amongst others
• Spare running rigging
• Tools
SAFETY EQUIPMENT:
Navigation Lights:
• Runnning lights, masthead, anchor, tricolour, steaming and foredeck lights (mostly LED)
Life saving:
• Active -XS-Dual Band Echomax Radar Reflector - 2020
• Ocean Signal Epirb1 406Mhz - 2019
• Ocean Signal AIS beacon - 2019
• Forties ISAF 6-man canister liferaft (serviced 2021)
• Ocean Safety 8-man canister liferaft (2022)
• 2x Oceansafety horseshoe buoys
• Stainless steel outboard crane with lift capacity for MOB recovery
• Danbuoy – 2019
• Drogue - 2019
• Gasoline redundancy bilge pump 2021
• Webbing jackstays
• Loud hailer/fog horn system
Fire & gas control:
• Fireboy engine shutdown controls in cockpit and at chart table (updated Spring 2023)
• Xintex propane monitor and two sensors
• Fire extinguishers throughout