The lifting keel gives a shallow 1’10” draught making her ideal for both cruising and inshore exploring. Drying moorings are easily accessible keeping running costs to a minimum.
The rig is optimised to make the boat easy to prepare for launching using a clever pivoting bowsprit making mast lifting safe and easy. The very simple track & strap mainsail attachments streamline the rigging process.
Unusually for a boat of this size the standard boat features a Yanmar 9hp inboard Diesel. This sets her apart from the other trailer sailors on the market.
The self draining cockpit is well protected with high coamings and has room for up to 6 adults. Spacious cockpit lockers to port and starboard offer dedicated battery, water and gas storage. Teak inlays are a stylish option.
Below deck the accommodation is satisfyingly generous including a well-appointed galley with a double gas burner and fully plumbed sink. A full size double forward v-berth is easily accessible from the saloon with 2 full length settee berths extending under the cockpit. A sea toilet can be fitted as an option under the forward berth.
Every boat is built to order with exterior colours and interior layout finished to your liking. Top quality deck fittings, sails and boom cover come as standard.
Hull Construction: Hand laid solid GRP hull with no foam core. Integral centerplate case laminated as part of the complete hull structure. Internal bunk and
forepeak moulding bonded into hull with internal structural bulkheads bonded to both hull and deck mouldings. Standard colours are Off White, Dark Blue
or Dark Green. The hull and deck joint is by way of an overlap or ‘Biscuit Tin Lid’ with GRP bonding.
Rudder: The rudder is transom hung on two stainless steel hangings bolted through the transom with Hardwood backing pads. The rudder is constructed
from laminated Plywood with a stainless steel lifting drop plate.
Engine Beds: Engine beds are incorporated in the GRP bunk moulding with mild steel mounts bonded into the bed design, which incorporates an oil drip
tray.
Ballast: Ballast is by way of iron punchings encapsulated in resin inside the hull keel moulding. A galvanised steel centerplate forms part of the ballast
with a stainless steel lifting wire leading to a winch lifting system operated from the cockpit.
Boot Top: A single boot top moulded in gel coat located above antifouling level. Colour in contrast to main hull and normally matching the deck.
Deck Construction: Hand laid GRP with Balsa core in way of horizontal load areas. Hard wood pads under deck fittings and stress points.
Cockpit : Cockpit locker lids are hand laid with Balsa core. There is integrated non-slip on horizontal surfaces with an optional two-tone colour. Cockpit
drains are located aft in the main foot well with additional drainage from the seats. Watertight lockers offer storage for batteries, water & gas. A central
locker houses the diesel engine when fitted.
Deck Fittings: Bespoke deck fittings including bowsprit, tabernacle and chain plates are made from stainless steel. 4 stainless steel deck cleats are
positioned aft & amidships with two fairleads feeding a teak sampson post forward. All sail controls are led aft to rope clutches / jammers with a single
halyard winch to starboard. Adjustable sheet cars. Access below is via a teak lined sliding companionway hatch and split plywood / Perspex washboards.
Extra ventilation provided by an aluminium forward hatch.
Ports: 2 aluminium fixed ports are fitted one each in the deck topsides.
Chain plates: Chain plates are in stainless steel and through bolted on the hull sides.
Vents: Ventilation is via a washboard vent and opening forward hatch.
Miscellaneous Equipment: Fuel filler &tank vent.(Inboard version only), Life harness attachment point by the companionway. Rope tidies for halyards.
Cockpit Lockers: Two main watertight lockers with latches and padlocks are provided. A padlock is also provided for the companionway hatch.
Mainmast: Laminated in Sitka Spruce and treated with Sikkens Cetol including a stainless steel mast band to take Cap shrouds, jib and mainsail halyards.
All deck mounted on a substantial stainless steel tabernacle.
Main Boom: Laminated in Sitka Spruce and treated with Sikkens Cetol including a Stainless steel gooseneck fitting, kicker and mainsheet bands and all
associated reefing line leads / terminals.
Bowsprit: Laminated in Sitka Spruce and treated with Sikkens Cetol including a stainless steel pivot fitting, end plate and bobstay take off points.
Gaff: Laminated in Sitka Spruce and treated with Sikkens Cetol including a Stainless steel gaff collar with rubber protection on bearing surface. Wire hoist
span and block.
Standing Rigging: Cap shrouds, lower shrouds & forestay in 4mm 1 x 19 stainless steel wire with swagged ends. Chromed rigging screws. Jib mounted on
reefing spar and controls led aft to cockpit.
Running Rigging: Main throat / peak halyards – 6mm braid. Jib &staysail halyards – 6mm braid. Main topping lift – 6mm braid. Mainsail reefing lines –
6mm braid. Mainsail outhaul – 6mm braid. Mainsheet & Jib sheets – 10mm sheet rope. All associated blocks for purchase tackles.
Mainsail: Dacron in tan or cream. 2 reef points with tie in lacing.
Jib: Dacron in tan or cream with wire luff and tell tails.
Boom Cover: In maroon, or cream acrylic. Fixings to allow for topping lift and mainsheet take off. All sails supplied with, sail numbers, logo and ties.
Engineering
Outboard Version
Outboard well: A teak engine mounting with stainless brackets. Engine well hull blank. GRP moulded fuel tank stowage and fuel lead splitter through aft
locker compartment. (fuel lead not supplied as standard)
Inboard Version
Stern Gear: A 1” stainless steel shaft is fitted connected to the engine via a coupling and fitted with a Tides Marine ‘lip seal’ gland. The shaft drives a fixed 2-bladed propeller.
Engine: Yanmar 1GM10 9hp marine diesel engine. A 55 amp (12V) alternator is fitted to the engine.
Engine Instruments and Controls: The engine instruments are located at the rear of the cockpit coaming and are recessed with a clear cover. Instruments
include audible alarm, alternator warning light, start switch and stop control. A single lever engine control is supplied and fitted in the cockpit well.
Engine Cooling: The engine is directly salt water cooled. A 1/2″ diameter pipe leads from the main seawater inlet through a strainer to the engine and
discharges overboard through the exhaust.
Engine Exhaust: A flexible exhaust hose connects the exhaust via a swan neck with water trap to the outlet fitting through the transom.
Fuel System: A plastic diesel tank with a capacity of approximately 38 litres, breather and integrated fuel gauge. The tank is fitted with flow and return
lines, the flow line having a manual shut off valve.
Plumbing
Bilge System: 1 x Manual bilge pump operated from the cockpit with a handle stored in the aft locker.
Fresh Water Tanks: 2 x 10ltr plastic jerry cans with manual hand pump. Also a bucket / sink.
Soil System: When fitted the heads discharge directly to sea via a vent loop and skin fitting.
Inlet / Outlet Fittings: Engine: In through a single skin fitting with a valve and strainer, out via the exhaust system.
Gas System: There is a double burner hob cooker attached to a separately stored gas bottle.
12 volt DC system
Batteries: Engine – one 12 volt 88 amp/hour. (Optional on outboard version)
Charging: Via main engine – a 35 amp (at 12 volt) alternator.
Switchboard: An optional switch panel is fitted to boats that have additional electronics fitted.
Miscellaneous Standard Equipment
Deck: 1 x winch handle. 1 x bilge pump handle stowed in aft cockpit locker. 1 x fire extinguisher – situated down below.
Joinery: The interior joinery is constructed from high quality materials and in accordance with good yacht practice. Bulkheads and side back linings are
from plywood.
Finish: All cabin woodwork is finished in a mix of painted bulkheads and varnished trim.
Soles: Laminate, teak and holly sole boards fitted as standard.
Upholstery: A choice of soft or wipe down plastic upholstery is available.